Our cut to length line consists of the following units, whose general characteristics and capacity parameters are given

• The uncoiling unit can open up to 25 tons of coils
• Servo pit pulling system determines the sheet length to be cut from the roll with tolerances below 1% and sends it to the guillotine shears
• It is a 6-high roller system and can be flatted-straightened without damaging to BA, painted coated surfaces.
• Pneumatic guillotine shears cut stainless steel up to 3mm
• The stacking device stacks the cut sheets on the pallet, ensuring that the long and short sides are neatly packed.
• The straightening unit has the ability to straighten stainless steel sheet up to 1600 mm wideness and 3 mm thickness by uncoiled from the coil.
• It has an electronic control mechanism to correct the thickness changes in the width of the rolled sheet.

Our grinding, brushing, edge banding line consists of the following units, whose general characteristics and capacity parameters are given

• The feeding unit and the conveyor allow the sheet metal plates on the pallet to be placed on the feeding conveyor with the vacuum mechanism and given to the grinding machine. In this way, sheets are processed without breaking, contamination, or any damage etc.
• Grinding-brushing machine, containing 2 calibrated sandpapers and 1 brush unit, can obtain duplex surfaces by grinding, brushing or both from 120 grit to 400 grit. It can process sheets up to 1600×4500 mm, in thickness between 0,5 – 4 mm. the powerful air suction and filtration system, not only it does not give dust to the atmosphere, but also cleans the ground surfaces.
• The banding line applies PE coating material from 10 microns to 100 microns on sheets up to 1600 mm width without any length restriction.
• The unloading and stacking unit ensures that the long and short sides form a neat package by taking the taped sheets over the conveyor belt with the vacuum mechanism and stacking them on the pallet.

• Manufactured on 2012,
• 4 brushes, sheet to sheet working,
• Brushing thickness 0,4 to 3 mm
• PVC laminating
• Working width 1500 mm
• Conveyor speed 5 to 15 m/ min

• The uncoiling unit can uncoil up to 20 tons of coils
• The slitting table can cut strips of desired width from stainless steel coils up to 3 mm  in thickness and up to 1600 mm in width
• Slitting thickness from 0,40 to 3 mm,
• Decoiling – recoiling capacity 15 mton
• Working speed up to 140 m/ min
• Laminating and paper inleave availability

• Manufactured on 2012,
• With 64 head,
• Polishing thickness 1 to 4 mm
• Working width 1500 mm
• Polishing 2B and BA surfaces
• Laminating and paper inleave availability

• 1mm – 3mm wall thickness range in the range of Q10 – Q168 diameter pipes are manufactured.
• 1mm – 3mm wall thickness range in the range of 10×10 – 80×100 diameter profiles are manufactured.
• We have 11 welded manufacturing machines.
• We have 11 surface treatment machines.

• From 0,7 mm to 4 mm working thickness
• Max. working width 2000 mm
• Laminating and paper inleave availability

• 1st line From 1 mm to 4 mm working thickness
• Pattern length 35 mm
• Pattern width 8 mm
• 2nd line from 4 mm up to 6 mm
• Max. working width 1500 mm

• The decoiler has a capacity of 30 tons.
• Flattening and cutting can be done in the range of 1.5 mm – 15 mm in quality suitable for laser cutting.
• 2000 mm width can be cut up to 15 meters in length.
• Our machine is equipped with 1 pre-straightening and 2 ironing systems that provide sheet metal straightening in laser cutting quality.
• The ironing system is hydraulic and is at a level to eliminate all roll errors.